Zero-Clearance Inserts Zero-Clearance Inserts Delta #DL-2 Leecraft Zero-Clearance Table Saw Insert 12-1/2"L x 3-3/4"W

Delta

Find the Leecraft Zero-Clearance Insert for your Delta Table Saw

Model DL-1U 13-3/8"L x 3-3/4"W x 1/2"T - Fits Delta models "Hybrid", 10" Contractor,10" Tilt Arbor Saw, 36-650, 36-714, Left-Tilt Contractor, UNISAW

Model DL-2 12-1/2"L x 3-3/4"W x 1/8"T - Fits Delta models 34-670, 34-740, 36-380, 36-600, QT-10, Super-10, TS-300, TS-350, XL-10

Model DL-3 10-15/16"L x 3-17/32"W - Fits Delta model Milwaukee 8" UNISAW

Model DL-4 24-25/32"L x 4-23/32"W - Fits Delta model RT-40

Model DL-5 10-5/32"L x 3-9/16"W - Fits Delta model 9" Rockwell

Model DL-6 14-1/2"L x 5"W x 1/2"T - Fits Delta NEW UNISAW (without Riving Knife Slot) models 36-L336, 36-L352, 36-L552

Model DL-7 14-1/2"L x 5"W x 1/2"T - Fits Delta NEW UNISAW (with Riving Knife Slot) models 36-L336, 36-L352, 36-L552

For step-by-step video installation CLICK HERE

 

#DL-2 Leecraft Zero-Clearance Table Saw Insert 12-1/2"L x 3-3/4"W
#DL-2 Leecraft Zero-Clearance Table Saw Insert 12-1/2"L x 3-3/4"W
Model:
DL-2
Price:
$31.99
Free Ground Shipping on Orders over $49!

#DL-2 Leecraft Zero-Clearance Table Saw Insert fits DELTA 10" DIRECT DRIVE - Models include #34-670, #34-740 (Super-10), #36-380 (XL-10) #36-600, QT-10, TS-300 & TS-350, JET #JSL-10TS SHOPLINE and #JTS-10DD

Use MicroJig MJ Splitter Kits for added table saw safety.  Available in THICK or THIN kerf they are easily installed and simple to align.  Not for use with Leecraft inserts that already have the riving knife slot cut in.  Intended for inserts WITHOUT the riving knife slot.

INSTALLING AND FITTING YOUR INSERT 

  1. Lower the blade completely.
  2. Place insert in table with finger hole at front and starter pocket located over blade.
  3. Securely fasten insert down with the two (2) original screws. If necessary, enlarge clearance holes in insert to facilitate proper alignment of screws.
  4. If insert is not adequately flush with table top, remove and shim up with tape or other material. Repeat step (3).

CUTTING THE BLADE SLOT (KERF)

  1. Check that insert is securely fitted, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance.
  2. Fully cover the insert with a board, and clamp at each end to the table saw top. This safety precaution will also greatly reduce any chip-out on top surface of insert when blade penetrates.
  3. Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR EYE PROCTECTION. Raise blade to maximum height at this time.
  4. Lower blade, turn off saw, and remove board. Your insert is now ready for use!

IMPORTANT TIPS FOR USE

  • Only recommended for use with carbide tipped cutters.
  • DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.
  • Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.
  • Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.

 

#DL-2 Leecraft Zero-Clearance Table Saw Insert 12-1/2"L x 3-3/4"W

 

  • Click to Load this Photo
  • Click to Load this Photo
Need help picking the correct Forrest Saw Blade or accessory?
See our Application Chart, or Contact Us for expert advice
Slivers
Mill
PREMIUM SAW BLADES and Industrial Cutting Tools