LEECRAFT INSERTS  >  Zero-Clearance Inserts  >  #HT-1 Leecraft Zero-Clearance Table Saw Insert 15-1/8"L x 3-3/4"Wx1/8"T

Zero-Clearance Inserts NEW! We are proud to offer LEECRAFT Zero-Clearance table saw inserts which are definitely SUPERIOR to any other brand! We think you'll agree that Leecraft's attention to detail and careful precision manufacturing are unmatched.

LEECRAFT Phenolic Table Saw Inserts reduce splintering and chip-out on the bottom side of regular or dado table saw cuts. The opening in the insert is cut on the table saw to the exact width of the saw blade’s kerf. The matching kerf prevents thin slices of wood from jamming in between the blade and the throat plate during a cut. It also reduces the amount of tear-out that can happen with a standard insert.

From the Manufacturer
The Zero Clearance concept is simple: the blade cuts its own perfectly sized slot by being raised through a machinable "blank" insert. Most inserts are 1/2-inch thick, high-density phenolic laminate, with a bonded-melamine surface. They offer superior rigidity, flatness, durability, and low friction and should not be confused with inferior HD/PP inserts. There's just no comparison! They feature leveling screws, side and end adjustment screws for a vibration-free fit, rear safety pin for lift-out protection, and a pre-cut blade bottom pocket that provides clearance for fully retracted blades and bevel cuts. (Some inserts use OEM screws to hold inserts in place). Instructions also included. Use carbide-tipped blades only. A pre-cut starter pocket makes cutting the clearance slot easy and a finger hole makes for simple removal and hanging. Colors may vary. Made in USA.

BEFORE ORDERING: MEASURE YOUR SAW THROAT OPENING TO PREVENT DELAYS. THEN CHECK BELOW TO FIND THE PROPER MODEL FOR YOUR TABLE SAW.

Model #BH-1 13-9/16"L x 3-3/4"W x 7/16" Thick - WITH RIVING KNIFE SLOT. Fits Bosch 4000 and 4100.

Model #BH-2 13-9/16"L x 3-3/4"W x 7/16" Thick - WITHOUT Riving Knife Slot for dado sets. Fits Bosch 4000 and 4100 models

Model #CR-1 14"L x 3-3/4"W x 3/16" Thick - Fits Sears CRAFTSMAN 10" belt-drive models 1977 to mid 2004 (Check size, see DL-1U), RIDGID TS2412, TS2424, TS2400, TS3612 (Please Note: CR-1 does not fit models TS2400LS, TS2400-1 or the new TS2410)

Model #CR-2 14-3/8"L x 3-3/4"W x 3/16" Thick - Fits Sears CRAFTSMAN, Older 10" belt-drive, Including models: 113.29901, 113.29903, 113.299040, 113.29943, 113.299142

Model #CR-3 14-3/8"L x 3-3/4"W x 3/32" Thick - Fits Sears CRAFTSMAN, Vintage 10" belt-drive, including models: 103.29992, 113.27520, 113.27610, 113.27970, 113.29920, 113.29990, 113.29991, 113.29992

Model #CR-4 15-1/8"L x 4-1/8"W x 1/8"T - Fits Sears CRAFTSMAN #351.218330

Model #DL-1U 13-3/8"L x 3-3/4"W - Fits DELTA: Unisaw & LEFT-TILT UNISAW, 10" Contractor, 10" Tilt Arbor Saw, "Hybrid" & Left-Tilt Contractor, Delta X5; GRIZZLY G1023; JET CTAS-10; POWERMATIC 63; CRAFTSMAN 22104, 22114, 22124; BRIDGEWOOD BW10TS; Steel City 35605, 35610, 35670, 35675, 35680, 35685

Model #DL-2 12-1/2"L x 3-3/4"W - Fits DELTA 10" DIRECT DRIVE - Models include #34-670, #34-740 (Super-10), #36-380 (XL-10) #36-600, QT-10, TS-300 & TS-350, JET #JSL-10TS SHOPLINE, JTS-10DD

Model #DL-614-1/2"L x 5"W - Fits NEW DELTA UNISAW Model #36-L336,36-L352, & 36-L552 WITHOUT riving knife slot

Model #DL-714-1/2"L x 5"W - WITH RIVING KNIFE SLOT fits NEW DELTA UNISAW Model #36-L336,36-L352, & 36-L552.

Model #DW-2 13-9/16"L x 3-3/4"W - Fits DeWALT: DW744 & DW745 (factory splitter/guard incompatible with DW-2 insert on these saws) & DW746

Model #GE-1 13-13/16" x 3-1/2" - Fits GENERAL International: 350 (Right Tilt) & 650 (Left Tilt)

Model #GE-2 14-31/32"L x 3-23/32"W - Fits GENERAL International: 50-220, 50-090K; JET: 10" Workshop Table Saw Newer Model-#JWTS-10 - older version (Stock #708100) (Please check size before ordering), JPS-10 Pro-Shop, JPS-10TS (Stock #708481, 708482, 708483, 708480K) and the Woodtek 10" Hybrid Table Saw

Model #GE-3 12-9/16"L x 3-9/16"W - Fits GENERAL International: 50-075/175/185/250/260

Model #HT-1 15-1/8"L x 3-3/4"W x 1/8"T - Fits HITACHI: C10FL & C10LA and Porter Cable PCB270TS

Model #JT-164 12-1/2" x 3-9/16" - Fits JET: JTS-10, JCS-10, Older Model-JWTS-10 (Please check size before ordering), JTAS-10, JWCS-10; POWERMATIC: 64 & 64A (left-tilt); SUNHILL: most 10" saws; BRIDGEWOOD: TSC-10C & TSC-10CL; KING KC 10GC; SHOP FOX: W1703, W1714, W1725, W1726; GRIZZLY: G0444, G0444Z, G0575, G0576

Model #JT-2L 13-5/16"L x 3-11/16"W - Fits JET XACTA SAW LEFT (JTAS-10XL); SHOP FOX: W1677, W1711; GRIZZLY G1023SL

Model #JT-5 15-5/16"L x 4-1/4"W - Fits JET Deluxe XACTA Saw - WITH RIVING KNIFE SLOT

Model #JT-6 15-5/16"L x 4-1/4"W - Fits JET Deluxe XACTA Saw for Dado Sets - WITHOUT riving knife slot

Model #JT-SS 12-9/16"L x 3-9/16"W - Fits Jet Super Saw JWSS-10LFR

Model #PM-1 14-7/16"L x 4"W - Fits POWERMATIC 66; BRIDGEWOOD BW10LTS

Model #PM-6 17-7/8"L x 4-1/4"W - Fits POWERMATIC PM2000 - WITH RIVING KNIFE SLOT

Model #PM-7 17-7/8"L x 4-1/4"W - Fits POWERMATIC PM2000 for Dado sets - WITHOUT riving knife slot

Model #RG-1 14"L x 3-3/4"W x 1/2" Thick - Fits ONLY RIDGID TS3650, TS3660

Model #RG-2 13-15/16"L x 3-3/4" W x 7/16" Thick - Fits RIDGID TS2400-1, TS2400LS, TS2410LS

Model #RG-3 14"L x 3-3/4"W x 3/8"T - WITH RIVING KNIFE SLOT fits the new RIDGID R4510

Model #RG-4 14"L x 3-3/4"W x 3/8"T - WITHOUT Riving Knife slot - fits the new RIDGID R4510

Model #RG-5 15-1/8"L x 3-3/4"W x 1/8"T - Fits RIDGID R4512 WITH RIVING KNIFE SLOT

Model #RG-6 15-1/8"L x 3-3/4"W x 1/8"T - Fits RIDGID R4512 WITHOUT Riving Knife slot For Dado Sets

Model #SC-1 14-11/16"L x 3-3/4"W x 1/2"T - Fits Steel City 10" Cabinet Saw Model #35900 Series - Rigid R4511, CRAFTSMAN 351.221160 WITH RIVING KNIFE SLOT

Model #SC-2 14-11/16"L x 3-3/4"W x 1/2"T - Fits Steel City 10" Riving Knife Cabinet Saw Model #35900 Series - Rigid R4511, CRAFTSMAN 351.221160 WITHOUT riving knife slot

#HT-1 Leecraft Zero-Clearance Table Saw Insert 15-1/8

#HT-1 Leecraft Zero-Clearance Table Saw Insert 15-1/8"L x 3-3/4"Wx1/8"T

Model:
HT-1
Price:
$26.99
Diameter:
Plate:
Bore:
Teeth:
Kerf:
Tooth Style:
This item qualifies for FREE SHIPPING in the US on orders over $35
SPECIAL PROMOTION - FREE GROUND SHIPPING IN THE US
Make a purchase of $35.00 or more and receive FREE GROUND SHIPPING in the US on select products!
#HT-1 Leecraft Zero-Clearance Table Saw Insert 15-1/8"L x 3-3/4"Wx1/8"T Hitachi C10FL & C10LA and Porter Cable PCB270TS

INSTALLING AND FITTING YOUR INSERT

  1. Lower the blade completely.
  2. Place insert in throat opening with finger hole towards operator and starter pocket located over blade. Back end of insert must be placed in first, allowing anti-lift lugs to slide under the cast iron ledge.
  3. Adjust leveling screws (supplied with saw) until insert is stable and flush with table top.
  4. Back out the adjusting screw to achieve a fit which is snug, yet removable. For added security, insert factory supplied hold down screw through the hole provided. Do not overtighten, as this will "spring" down the front.
  5. SPLITTER: If your saw has a splitter, you will need to cut a slot at the rear of the insert to accommodate it. Trace the outline of the slot from your original metal insert, and cut with bandsaw or hacksaw. Leave the bridge between the splitter slot and the blade slot as thick as possible.

CUTTING THE BLADE SLOT (KERF)

  1. Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance.
  2. Fully cover the insert with a board, and clamp at each end to the table saw top.
  3. Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES. Raise blade to maximum height at this time.
  4. Lower blade, turn off saw, and remove board. Your insert is now ready for use!

IMPORTANT TIPS FOR USE

  • Only recommended for use with carbide tipped cutters.
  • DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.
  • Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.
  • Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.
#HT-1 Leecraft Zero-Clearance Table Saw Insert 15-1/8"L x 3-3/4"Wx1/8"T

 

Click to Load this Photo Click to Load this Photo
Need help picking the correct Forrest Saw Blade or accessory?
See our Application Chart, or Contact Us for expert advice
We proudly accept Visa, MasterCard, Discover and American Express, as well as PayPalVerified by PayPal
Slivers Mill - © Copyright 2001-Present

Website Development and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company