Zero-Clearance Inserts Zero-Clearance Inserts Jet #JT-7 Leecraft Zero-Clearance Table Saw Insert 14"L x 4-1/8"W With RIVING KNIFE SLOT
Find the Leecraft Zero-Clearance Insert for your Jet Table Saw
Model DL-1U 13-3/8"L x 3-3/4"W - Fits Jet model CTAS-10
Model DL-2 12-1/2"L x 3-3/4"W - Fits Jet models JSL-10TS, JTS-10DD, Shopline
Model GE-2 14-31/32"L x 3-23/32"W - Fits Jet models 708100, 708481, 708482, 708483, 10" Workshop Table Saw, 708480K, JPS-10 ProShop
Model JT-164 12-1/2"L x 3-9/16"W - Fits Jet models JTS-10, JCS-10, JTAS-10, JWCS-10, JWTS-10
Model JT-2L 13-5/16"l x 3-11/16"W - Fit Jet models JTAS-10XL, XACTA Saw Left
Model JT-5 15-5/16"L x 4-1/4"W - Fits Jet model Deluxe XACTA Saw
Model JT-6 15-5/16"L x 4-1/4"W - Fits Jet model Deluxe XACTA Saw WITHOUT riving knife slot for dado or angle cuts
Model JT-7 14"L x 4-1/8"W - Fits Jet models 708490, 708491, 708492, 708493, 708494, 708495, JPS-10TS ProShop
Model JT-8 14"L x 4-1/8"W - Fits Jet models 708490, 708491, 708492, 708493, 708494, 708495, JPS-10TS ProShop WITHOUT riving knife slot for dado or angle cuts
Model JT-SS 12-9/16"L x 3-9/16"W - Fits Jet models JWSS-10LFR, JWSS-10PF, JWSS-10SPF, JWSS-CS, Super Saw
For step-by-step installation video CLICK HERE
BEFORE ORDERING: MEASURE YOUR SAW THROAT OPENING OR CURRENT INSERT AND COMPARE TO THE MEASUREMENTS GIVEN ON OUR WEBSITE. Jet has similar models with different size throat openings.
#JT-7 Leecraft Zero-Clearance Table Saw Insert 14"L x 4-1/8"W with RIVING KNIFE SLOT for NEW Jet JPS-10TS ProShop, Jet #708490, #708491, #708492, #708493, #708494, #708495. Also fits the 1.75 HP 10” Laguna Fusion saw, Grizzly: G0661, G0713, G0732 and Baileigh TS-1044H.
The Zero Clearance concept is simple: the blade cuts its own perfectly sized slot by being raised through a machinable "blank" insert. Most inserts are 1/2-inch thick, high-density phenolic laminate, with a bonded-melamine surface. They offer superior rigidity, flatness, durability, and low friction and should not be confused with inferior HD/PP inserts. There's just no comparison! They feature leveling screws, side and end adjustment screws for a vibration-free fit, rear safety pin for lift-out protection, and a pre-cut blade bottom pocket that provides clearance for fully retracted blades and bevel cuts. (Some inserts use OEM screws to hold inserts in place). Instructions also included. Use carbide-tipped blades only. A pre-cut starter pocket makes cutting the clearance slot easy and a finger hole makes for simple removal and hanging. Colors may vary. Made in USA.
Use MicroJig MJ Splitter Kits for added table saw safety. Available in THICK or THIN kerf they are easily installed and simple to align. Not for use with Leecraft inserts that already have the riving knife slot cut in. Intended for inserts WITHOUT the riving knife slot.