Zero-Clearance Inserts Zero-Clearance Inserts Craftsman #CR-4 Leecraft Zero Clearance Insert 15-1/8"L x 4-1/8"W x 1/8"T


Find the Leecraft Zero-Clearance Insert for your Craftsman Table Saw

Model CR-1 14"L x 3-3/4"W x 3/16"T - Fits Craftsman belt drive models 1977 to mid 2004 (check size, see DL-1U)

Model CR-2 14-3/8"L x 3-3/4"W x 3/16"T - Fits Craftsman models 113.29901, 113.29902, 113.29903, 113.29904, 113.299142, 113.29943, 113.29960

Model CR-3 14-3/8"L x 3-3/4"W x 3/32"T - Fits Craftsman models 103.29992, 113.22411, 113.27520, 113.27610, 113.27970, 113.29920, 113.29990, 113.29991, 113.29992 

Model CR-4 15-1/8"L x 4-1/8"W x 1/8"T - Fits Craftsman models 351-218330, 21833

Model DL-1U 13-3/8"L x 3-3/4"W x 1/2"T - Fits Craftsman models 22104, 22114, 22124

Model SC-1 14-11/16"L x 3-3/4"W x 1/2"T - Fits Craftsman model 351.221160

Model SC-2 14-11/16"L x 3-3/4"W x 1/2"T - Fits Craftsman model 351.221160

For step-by-step installation video CLICK HERE

#CR-4 Leecraft Zero Clearance Insert 15-1/8"L x 4-1/8"W x 1/8"T
#CR-4 Leecraft Zero Clearance Insert 15-1/8"L x 4-1/8"W x 1/8"T
Free Ground Shipping on Orders over $49!

CR-4 Leecraft Zero Clearance Table Saw Insert fits Sears CRAFTSMAN #351.218330, Dayton 4KXD1, Grizzly G0715P, Masterforce 240-0036 and RIKON 10-2015.

Use MicroJig MJ Splitter Kits for added table saw safety. Available in THICK or THIN kerf they are easily installed and simple to align. Not for use with Leecraft inserts that already have the riving knife slot cut in. Intended for inserts WITHOUT the riving knife slot.


  1. Remove riving knife (RK) and lower the blade completely.
  2. Place insert in throat opening with finger hole towards operator and starter pocket located over blade. Back end of insert must be placed in first, allowing anti-lift lug to slide under the cast iron ledge. Insert should be resting on TOP of the 4 leveling screws, just like the original factory insert is designed to do.
  3. Adjust leveling screws (through access holes provided) until insert is table and flush with table top.
  4. Back out the adjusting screw to achieve a fit which is snug, yet removable. Note: This insert does NOT utilize the magnet located in the front of your throat opening. This insert is held in place by lateral friction once the adjusting screw has been backed out.


  1. Check that insert is fitted properly and that the blade is clear.
  2. Fully cover the insert with a board, and clamp at each end to the table saw top.
  3. Reconnect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES.
  4. Raise blade to maximum desired height at this time.
  5. Lower blade, turn off saw, and remove board.
  6. RIVING KNIFE (RK): To accommodate the RK, you will need to finish cutting out the optional pre-routed RK slot, using a saw or router. This becomes simple and extension of the blade slot.


  • Only recommended for use with carbide tipped cutters.
  • DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.
  • Under certain condtiions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.
  • Ideally, a separate insert should be used with each blade, dado stack, or angle setup. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.


#CR-4 Leecraft Zero Clearance Insert 15-1/8"L x 4-1/8"W x 1/8"T


  • Click to Load this Photo
  • Click to Load this Photo
Need help picking the correct Forrest Saw Blade or accessory?
See our Application Chart, or Contact Us for expert advice
PREMIUM SAW BLADES and Industrial Cutting Tools