Zero-Clearance Inserts Zero-Clearance Inserts Craftsman #CR-2 Leecraft Zero-Clearance Table Saw Insert 14-3/8"L x 3-3/4"W x 3/16"T

Craftsman

Find the Leecraft Zero-Clearance Insert for your Craftsman Table Saw

Model CR-1 14"L x 3-3/4"W x 3/16"T - Fits Craftsman belt drive models 1977 to mid 2004 (check size, see DL-1U)

Model CR-2 14-3/8"L x 3-3/4"W x 3/16"T - Fits Craftsman models 113.29901, 113.29902, 113.29903, 113.29904, 113.299142, 113.29943, 113.29960

Model CR-3 14-3/8"L x 3-3/4"W x 3/32"T - Fits Craftsman models 103.29992, 113.22411, 113.27520, 113.27610, 113.27970, 113.29920, 113.29990, 113.29991, 113.29992 

Model CR-4 15-1/8"L x 4-1/8"W x 1/8"T - Fits Craftsman models 351-218330, 21833

Model DL-1U 13-3/8"L x 3-3/4"W x 1/2"T - Fits Craftsman models 22104, 22114, 22124

Model SC-1 14-11/16"L x 3-3/4"W x 1/2"T - Fits Craftsman model 351.221160

Model SC-2 14-11/16"L x 3-3/4"W x 1/2"T - Fits Craftsman model 351.221160

 

#CR-2 Leecraft Zero-Clearance Table Saw Insert 14-3/8"L x 3-3/4"W x 3/16"T
#CR-2 Leecraft Zero-Clearance Table Saw Insert 14-3/8"L x 3-3/4"W x 3/16"T
Model:
CR-2
Price:
$28.99
This item qualifies for FREE SHIPPING in the US on orders over $49
SPECIAL PROMOTION - FREE GROUND SHIPPING IN THE US
Make a purchase of $49.00 or more and receive FREE GROUND SHIPPING in the US on select products!
#CR-2 Leecraft Zero-Clearance Table Saw Insert 14-3/8"L x 3-3/4"W x 3/16"T, Sears CRAFTSMAN, OLDER 10" belt-drive, including models: 113.29901, 113.29903, 113.299040, 113.29943, 113.299142

Use MicroJig MJ Splitter Kits for added table saw safety.  Available in THICK or THIN kerf they are easily installed and simple to align.  Not for use with Leecraft inserts that already have the riving knife slot cut in.  Intended for inserts WITHOUT the riving knife slot. 


INSTALLING AND FITTING YOUR INSERT

  1. Lower the blade completely.
  2. Place insert in table with end-adjustment screw at front and starter pocket located over blade. If insert will not fit into table opening due to interference with ledge, carefully remove material from underside of insert as required, by filing, sanding, routing, etc.
  3. Using 3/32" Allen (hex) wrench, run leveling screws down until insert is stable and flush with table top.
  4. Back out side-adjustment screw, and then end-adjustment screw to achieve a fit that is snug, yet removable. Note: To remove insert, a thin stick, etc. may be inserted into kerfed insert. Alternately, a 3/4" diameter finger hole could be bored near front of insert to facilitate removal.

CUTTING THE BLADE SLOT (KERF)

  1. Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance.
  2. Fully cover the insert with a board, and clamp at each end to the table saw top.
  3. Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES. Raise blade to maximum height at this time.
  4. Lower blade, turn off saw, and remove board. Your insert is now ready for use!

IMPORTANT TIPS FOR USE

  • Only recommended for use with carbide tipped cutters.
  • DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.
  • Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.
  • Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.
#CR-2 Leecraft Zero-Clearance Table Saw Insert 14-3/8"L x 3-3/4"W x 3/16"T

 

  • Click to Load this Photo
  • Click to Load this Photo
Need help picking the correct Forrest Saw Blade or accessory?
See our Application Chart, or Contact Us for expert advice
Slivers
Mill
PREMIUM SAW BLADES and Industrial Cutting Tools