Zero-Clearance Inserts Zero-Clearance Inserts Shop Fox #JT-2L Leecraft Zero-Clearance Table Saw Insert 13-5/16"L x 3-11/16"W

Shop Fox

Find the Leecraft Zero-Clearance Insert for your Shop Fox Table Saw

Model CR-4 15-1/8"L x 4-1/8"W - Fits Shop Fox W1851, 1824

Model JT-164 12-1/2"L x 3-9/16"W - Fits Shop Fox models W1703,W1714, W1725 and W1726

Model JT-2L 13-5/16"L x 3-11/16"W - Fits Shop Fox models W1677 and W1711

Model RG-5 15-1/8"L x 3-3/4"W x 1/8"T - Fits Shop Fox model 1837 with Riving Knife slot

Model RG-6 15-1/8"L x 3-3/4"W x 1/8"T - Fits Shop Fox model 1837 WITHOUT Riving Knife slot

For step-by-step installation video CLICK HERE

#JT-2L Leecraft Zero-Clearance Table Saw Insert 13-5/16"L x 3-11/16"W
#JT-2L Leecraft Zero-Clearance Table Saw Insert 13-5/16"L x 3-11/16"W
Free Ground Shipping on Orders over $49!

#JT-2L Leecraft Zero-Clearance Table Saw Insert 13-5/16"L x 3-11/16"W, Jet XACTA SAW LEFT(JTAS - 10XL); SHOP FOX W1677, W1711; GRIZZLY G1023SL & 1023RL.

Use MicroJig MJ Splitter Kits for added table saw safety.  Available in THICK or THIN kerf they are easily installed and simple to align.  Not for use with Leecraft inserts that already have the riving knife slot cut in.  Intended for inserts WITHOUT the riving knife slot. 


  1. Lower the blade completely.
  2. Place insert in table with adjustment screw at front, and starter pocket located over blade.
  3. Run leveling screws down until insert is stable and flush with table top.
  4. Back out end-adjustment screw and side adjustment screw to achieve a fit that is snug, yet removable.
  5. If the insert will not go down flush with table top because it is resting on top of blade, then raise up using leveling screws until insert is sitting steady about 1/16" above table top. This should provide adequate clearance for blade.
  6. SPLITTER: If your saw has a splitter, you’ll need to cut a slot at the rear of the insert to accommodate it. Trace the outline of the slot from your original metal insert, and cut with bandsaw or hacksaw. Leave the bridge between the splitter slot and the blade slot as thick as possible.


  1. Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance.
  2. Fully cover the insert with a board, and clamp at each end to the table saw top.
  3. Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES. Raise blade to maximum height at this time.
  4. Lower blade, turn off saw, and remove board. Your insert is now ready for use!


  • Only recommended for use with carbide tipped cutters.
  • DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.
  • Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.
  • Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.
#JT-2L Leecraft Zero-Clearance Table Saw Insert 13-5/16"L x 3-11/16"W


  • Click to Load this Photo
  • Click to Load this Photo
Need help picking the correct Forrest Saw Blade or accessory?
See our Application Chart, or Contact Us for expert advice
PREMIUM SAW BLADES and Industrial Cutting Tools